Cherry IPA

title 1
Cherry IPA
⏱️ cook time 1 hour 20 minutes
🍽️ servings 8
⚡ Difficulty medium

intro

Bright tart-sweet cherries meet bold, citrusy Cascade hops in this smooth homebrewed IPA, with a crisp dry finish perfect for sipping at summer backyard gatherings.

Ingredients

Filtered cold water 4L
Pale liquid malt extract 900g
Fresh dark sweet cherries 450g
Cascade hop pellets 28g
American ale yeast (US-05) 5g
Light demerara sugar 50g

Steps

1

Sanitize All Equipment

Spray every surface of the stock pot, stirring spoon, thermometer, strainer, fermentation jug, airlock, siphon, bottles, and capper with no-rinse food-safe sanitizer from the spray bottle. Wipe lightly with a clean section of the light blue cotton towel, then allow to air dry for 2 minutes. Confirm no residual suds are visible on any surface — even tiny amounts of unsanitized residue can introduce wild bacteria that spoil the final beer.

Step 1
step1:Sanitize All Equipment
2

Heat Malt Extract Base

Pour 3 liters of filtered water into the stainless steel stock pot, set on the induction cooktop over medium heat, and bring to a gentle rolling boil (100°C / 212°F). Slowly stir in the full 900g of pale liquid malt extract with the slotted stainless steel spoon, stirring constantly until fully dissolved, with no thick malt clumps sticking to the pot bottom. Adjust heat to maintain a gentle boil, watching closely to prevent sticky boilovers.

Step 2
step2:Heat Malt Extract Base
3

Add Bittering Hops

Once the malt extract is fully dissolved and the wort holds a steady gentle boil, add 14g (half the total portion) of Cascade hop pellets directly to the pot. Set a timer for 45 minutes, maintaining the soft rolling boil with the pot uncovered — covering the pot traps volatile hop compounds that create harsh, grassy off-flavors. Stir gently every 10 minutes to prevent hop material from sticking and burning on the pot bottom.

Step 3
step3:Add Bittering Hops
4

Pit Fresh Cherries

While the wort boils, place the 450g of fresh dark cherries in the small stainless steel mixing bowl. Use the cherry pitter to remove every pit, applying firm pressure to push the pit out through the stem end of each cherry. Tear each pitted cherry in half to release its sweet juice, discarding all pits and any bruised, soft, or moldy fruit. Set the prepared cherries aside until the final 5 minutes of the boil.

Step 4
step4:Pit Fresh Cherries
Step 4
step4:Pit Fresh Cherries
5

Add Cherries and Aroma Hops

When the 45-minute boil timer shows 5 minutes remaining, add all pitted, halved cherries and 7g (quarter of total) Cascade hop pellets to the boiling wort. Stir once gently to fully submerge all fruit and hops. When the timer goes off, turn off the induction burner, add the final 7g of Cascade hops for bright aroma, and stir once to incorporate.

Step 5
step5:Add Cherries and Aroma Hops
6

Cool and Strain Wort

Place the lid on the stock pot, then carefully move the pot to an ice bath (out of frame) to cool the wort to 21°C / 70°F as quickly as possible, approximately 20 minutes. Check temperature regularly with the digital thermometer — never add yeast until the wort is below 24°C / 75°F, as high heat will kill the yeast cells. Once cooled, pour the wort through the fine-mesh strainer into the 1-gallon glass fermentation jug to filter out hop debris and cherry skins.

Step 6
step6:Cool and Strain Wort
Step 6
step6:Cool and Strain Wort
7

Pitch Yeast and Ferment

Top up the fermentation jug with remaining filtered cold water to reach the etched 1-gallon volume mark. Sprinkle the full 5g packet of American ale yeast evenly over the surface of the cooled wort. Fill the airlock halfway with sanitizer solution, fit it into the rubber stopper, and seal the jug mouth tightly. Give the jug a gentle swirl to distribute the yeast, then store it in a dark, temperature-stable 18-21°C / 65-70°F space for 14 days, until bubbling in the airlock stops completely for 48 hours.

Step 7
step7:Pitch Yeast and Ferment
8

Bottle and Carbonate

After fermentation is complete, dissolve the 50g of demerara sugar in 50ml of boiling water, cool to room temperature, and divide evenly between 8 sanitized 12oz glass bottles. Use the auto-siphon to transfer the clear beer from the fermentation jug into the bottles, leaving 2cm of headspace at the top of each bottle. Cap bottles tightly with the capper and crown caps, then let sit at room temperature for 7 days to build natural carbonation. Chill bottles for 48 hours before serving.

Step 8
step8:Bottle and Carbonate

Tips

1.Never skip sanitizing all equipment that touches cooled wort or beer: wild yeast and bacteria from unwashed surfaces create sour, vinegary off-flavors that can ruin an entire batch, and no-rinse brewer’s sanitizer works effectively without leaving soapy residue.
2.Use only fully ripe, unblemished dark sweet cherries for the best flavor: underripe cherries add sharp, astringent tartness, while overripe or bruised fruit adds musty, fermented off-notes, so taste one cherry before adding it to the wort to confirm it is sweet and juicy.
3.Add the final portion of hops only after turning off the heat: extended boiling breaks down the delicate citrus and pine essential oils in Cascade hops, leaving only harsh bitterness instead of the bright, aromatic hop character that defines a great IPA.

✨ You May Also Like

Drinks & Beverages
🍜 Mexico

A bright, balanced tequila-based cocktail with zesty fresh lime, smooth orange liqueur, and a signature salt rim, perfect for warm summer sipping.

⏱️ 5 minutesDrinks & Beverages ★ 4.9
Drinks & Beverages
🍜 United States

Thick, creamy, nostalgic classic vanilla milkshake with a rich, smooth texture, topped with whipped cream and a cherry for cool, sweet refreshment.

⏱️ 5 minutesDrinks & Beverages ★ 4.7
Drinks & Beverages
🍜 United States

A bright, golden strong ale with fruity banana-clove notes, subtle hop spice, and soft carbonation, brewed in classic Trappist Tripel tradition.

⏱️ 2 hours aDrinks & Beverages ★ 4.5
Drinks & Beverages
🍜 United States

A frothy, nostalgic American soda fountain treat pairing bubbly cold root beer with creamy vanilla ice cream, perfect for cooling down at warm weather gatherings.

⏱️ 20 minuteDrinks & Beverages ★ 4.8
Drinks & Beverages
🍜 United States

Tart, funky, effervescent American Wild Ale is a complex fruity craft beer brewed with wild yeast, delivering bright, zesty notes perfect for warm-weather sipping.

⏱️ 2 hours aDrinks & Beverages ★ 4.4
Drinks & Beverages
🍜 United States

Bright, bubbly copycat of the iconic American caramel cola, balanced with citrus and warm spice, perfect for sipping ice-cold on hot days.

⏱️ 15 minuteDrinks & Beverages ★ 4.8

Cherry IPA:Frequently Asked Questions

1.Can I use frozen cherries instead of fresh dark sweet cherries for this recipe? ▾
Absolutely! Frozen dark sweet cherries work perfectly, and often have more consistent flavor than out-of-season fresh fruit. Thaw them fully, gently crush to release juice, and skip pre-sweetened frozen options, as extra added sugar will ruin the crisp, dry finish. A quick 10-minute low simmer to pasteurize is a smart move to prevent wild yeast contamination.
2.Why does this recipe call for filtered cold water instead of regular tap water? ▾
Unfiltered tap water often has chlorine, chloramine, or heavy mineral off-notes that dull the bright citrus of Cascade hops and make cherry flavor taste flat. Filtered cold water has a neutral profile that lets tart-sweet cherry and hoppy notes shine, without adding odd chemical aftertastes that would ruin your final batch of IPA.
3.How long do I need to let this cherry IPA ferment before it’s ready to drink? ▾
Plan for 3 to 4 weeks total from brew day to first sip. Primary fermentation with US-05 yeast takes 7 to 10 days, then you’ll add crushed cherries for a 7 to 10 day secondary fruit steep, followed by 3 to 5 days of bottle conditioning to build carbonation before chilling and serving.
4.Can I substitute Cascade hop pellets with another hop variety if I can’t find them? ▾
Cascade is classic for its bright citrus, piney punch that pairs perfectly with cherries, but you can swap in Centennial or Citra pellets in a pinch. Stick to the same total hop weight to keep the IPA’s bold hop balance right, and avoid super earthy, floral hops that will clash with bright cherry flavor.
5.Do I need to pit the cherries before adding them to my brew? ▾
Yes, always pit your cherries first! Cherry pits contain small amounts of amygdalin, which can break down into bitter, almond-like off-flavors (and trace undesirable compounds) during fermentation. Pitting takes a little extra prep time, but it prevents harsh, unpleasant notes from ruining your smooth final beer.
6.What makes US-05 American ale yeast a good pick for this cherry IPA? ▾
US-05 is a clean, fast-fermenting neutral ale yeast that ferments dry and crisp, without adding heavy estery or funky yeast notes that would compete with cherry and Cascade hop flavors. It’s also extremely forgiving for new homebrewers, with high alcohol tolerance and consistent, reliable results every batch.
7.When is the best time to add cherries to get the brightest, truest fruit flavor? ▾
Add your crushed, pasteurized cherries after primary fermentation finishes, when the beer has already dropped most of its initial sediment. Adding fruit too early blows off delicate cherry aroma during active fermentation and causes stubborn pectin haze, while post-primary addition locks in that bright tart-sweet note.
8.How carbonated should this cherry IPA be when it’s fully finished? ▾
Aim for a medium carbonation level, around 2.2 to 2.5 volumes of CO2, which matches the crisp, refreshing profile this recipe is designed for. That fizz level is enough to lift bright citrus hop and cherry aromas when you pour, without being so bubbly that it feels gassy or overwhelms the smooth malt backbone.
9.Can I use store-bought cherry puree instead of whole fresh or frozen cherries? ▾
You can, but stick to unsweetened, 100% cherry puree with no added preservatives. Preservatives like potassium sorbate will stop your yeast from working properly, leading to flat, under-fermented beer. Use about 20% less puree by weight than whole crushed cherries, since puree is more concentrated and can make beer overly sweet.
10.Why do I get a hazy pour even after I let the beer condition fully? ▾
Light haze is totally normal for fruit-forward homebrewed IPAs, usually from tiny cherry pectin particles or hop sediment that stays suspended. If you want a clearer beer, give your secondary ferment a 2 to 3 day cold crash at 38°F in the fridge before bottling to drop most suspended sediment out for a crisper pour.
11.How long will this homebrewed cherry IPA stay fresh after bottling? ▾
Stored in a cool, dark place away from direct sunlight and temperature swings, this IPA will taste its best for 3 to 4 months after bottling. Bright Cascade hop aroma will fade first after that point, and cherry notes will mellow, so drink it within that window to get that perfect tart-sweet, citrusy balance.
12.Do I need fancy, expensive homebrewing equipment to make this recipe? ▾
You don’t need high-end gear at all! A basic 5-gallon homebrewing kit with a food-grade fermentation bucket, airlock, siphon, bottling wand, and bottle capper is all you need. Just make sure every piece of equipment is fully sanitized before you start, since stray bacteria is the top cause of off-flavors.
13.Will this IPA turn out overly sweet if I add the full recommended amount of cherries? ▾
Not if you follow the fermentation timeline correctly! US-05 yeast will ferment a good portion of the natural cherry sugar during the secondary steep, leaving just a subtle tart-sweet cherry note against the dry malt finish. If you prefer a drier beer, cut the cherry amount by 25% to tone down residual fruit sweetness.
14.What temperature should I keep my fermentation at for the best results? ▾
Keep primary fermentation steady between 65°F and 68°F for US-05 yeast. That range lets the yeast work cleanly, without producing harsh solvent-like off-flavors that pop up if fermentation gets too warm, or stalling out completely if it gets too cold. Drop the temp a few degrees once you add cherries to help sediment settle.
15.Can I dry hop this IPA for extra hop aroma if I want a bolder flavor? ▾
Absolutely! Add 1 extra ounce of Cascade hop pellets 3 days before you plan to bottle, for an extra punch of bright citrus, piney hop aroma that pairs beautifully with cherries. Don’t add dry hops earlier than that, or you’ll lose most of that delicate hop aroma out the airlock during late active fermentation.
16.Why does my cherry IPA taste harsh or medicinal right after carbonation finishes? ▾
That’s totally normal “green beer” flavor that shows up immediately after carbonation! Let the bottles condition for an extra 5 to 7 days in a cool, dark spot, and those harsh, young flavors will mellow out completely as the beer matures. Rushing conditioning is the most common reason new brewers think their batch failed.
17.What serving temperature works best for this cherry IPA? ▾
Serve this beer chilled to 42°F to 45°F, just a touch warmer than standard mass-market lager. That temperature is cold enough to keep the finish crisp and refreshing for summer backyard sipping, but not so ice-cold that you mute the bright tart cherry flavor and zesty Cascade hop notes that make this IPA special.
18.Can I make a non-alcoholic version of this cherry IPA at home? ▾
You can, but you’ll need to adjust the process to limit alcohol production. Use a low-alcohol yeast strain made for NA beer, stop fermentation early once you hit less than 0.5% ABV, then pasteurize the batch to halt yeast activity before adding cherry flavor and carbonating. Expect slightly different texture and hop balance than the standard version.
19.How do I avoid getting floating cherry bits in my finished poured beer? ▾
When you add crushed cherries to secondary, put them in a sanitized fine-mesh hop bag weighted down with a sanitized stainless steel weight to keep them contained. When siphoning beer for bottling, leave the bottom inch of liquid (where settled fruit and yeast sediment sits) in the fermentation bucket instead of transferring it to bottles.

Comments (3)

3 days ago

OMG, this cherry IPA recipe was a total game changer for my weekend brew day! I was worried the cherry would make it cloyingly sweet, but the balance between the bright citrus hop bite and tart cherry is *chef’s kiss*. Brought a growler to our neighborhood potluck last weekend and everyone was begging for the recipe — even my buddy who swears he hates any fruit in beer went back for three refills. Quick note: I used frozen dark sweet cherries instead of fresh because they were sold out at my grocery store, and it still turned out SO good. Cook time was exactly as listed too, no weird hidden steps or random fancy equipment required.

2 days ago

Wait, did you add the cherries during primary or secondary fermentation? I messed up a peach wheat beer last year by adding fruit too early and got that weird solventy off-flavor, would love to not repeat that mistake when I brew this next month!

yesterday

So glad this was a hit at your potluck, Mike! Frozen cherries are actually a fantastic swap here — they break down easier to release that bright tart cherry flavor, so no issues there at all. To answer Jess’s question too: add the pitted, crushed cherries during the last 10 minutes of the boil for this recipe, no secondary addition needed, which helps avoid those tricky off-flavors from fruit sitting in the fermenter too long!

1 week ago

I’ve been nervous to try homebrewing for ages because I thought it’d be way too complicated and take all weekend, but this medium-difficulty cherry IPA was totally doable even as a total newbie! My husband has been obsessed with craft IPAs lately so I made this for his birthday cookout with his friends, and they all said it tasted like something you’d pay $18 for a four-pack at our local taproom. The only hiccup I had was underestimating how much headspace I needed in my fermenter, so I had a tiny overflow mess on my counter, but that was totally my bad, not the recipe’s fault. 10/10 will be making this again for our fall tailgate in a few weeks!

5 days ago

Happy to hear this was approachable for your first homebrew, Liz! The headspace overflow is such a common first-timer misstep, no shame at all — I’ll add a quick note to the recipe tips section reminding folks to leave that extra 1-2 inches of room for fermentation bubbling to prevent messes. Hope your husband had an amazing birthday!

2 weeks ago

Solid recipe, the cherry flavor comes through really nicely without tasting like cheap candy syrup, which is my biggest pet peeve with store-bought and homebrewed fruit IPAs. I bumped up the dry hop addition by half an ounce of Citra because I love that extra tropical punch, and it paired insanely well with the tart cherry. Made a batch for my fantasy football draft night last week, and the whole league was raving about it. Only reason I’m not giving it a full 5 stars is I wish the recipe had a note about expected final ABV so I could plan accordingly for drinkers who are driving, but otherwise it’s top tier. Will absolutely brew this again once this keg kicks.