Milkshake IPA Craft Beer
intro
Creamy, hazy, fruit-forward Milkshake IPA with soft vanilla notes, minimal bitterness, and a lush smoothie-like mouthfeel—ideal for warm summer sipping.
Ingredients
Steps
Mash the Grain Bill
Heat 1 gallon of filtered water in the stainless steel brew kettle to 152°F, monitored with the digital thermometer. Add crushed 2-row pale malt, wheat malt, and flaked oats, stirring with the long stainless steel spoon to eliminate dry clumps. Hold the mash temperature steady at 150–154°F for 60 minutes, covering the kettle and checking temperature every 10 minutes. The finished mash will smell sweet and bready, with a thick, porridge-like consistency.
Strain and Sparge Mash
After the 60-minute mash rest, place the fine mesh strainer over the brew kettle, then slowly pour the mash through to separate sweet wort from grain solids. Slowly pour 0.5 gallons of 170°F filtered water over the spent grains in the strainer to rinse residual sugars (sparging), collecting all runoff wort back into the kettle. The collected wort should be pale, clear gold, free of large grain particles.
Boil Wort and Lactose
Place the brew kettle over heat and bring the collected wort to a gentle, rolling boil (212°F at sea level). Once boiling, add all measured lactose powder, stirring to fully dissolve. Maintain a gentle boil for 60 minutes, adjusting heat as needed to avoid boilovers. Do not add bittering hops at this stage to keep the beer soft and low in perceived bitterness.
Add Whirlpool Adjuncts
After the 60-minute boil, turn off heat and let the wort cool to 170°F. Add the 0.3 oz Citra whirlpool hop pellets and the split, scraped vanilla bean (seeds and pod), stirring vigorously to create a slow, gentle whirlpool. Let the mixture rest for 20 minutes to extract bright hop aroma and warm vanilla flavor without adding harsh bitterness. The wort will smell intensely of tropical citrus and sweet vanilla.
Cool and Pitch Yeast
Surround the base of the brew kettle with reusable ice packs on the counter until the wort cools to 68°F, verified with the thermometer (temperatures above 75°F will kill the yeast). Pour the cooled wort through the fine mesh strainer into the clean 1-gallon glass carboy, leaving all hop and vanilla sediment behind in the kettle. Sprinkle the entire packet of London Ale III yeast onto the wort surface, then seal the carboy with the rubber stopper and sanitizer-filled airlock. The transferred wort will be hazy pale gold.
Complete Primary Fermentation
Leave the sealed carboy undisturbed in a dark, 68°F temperature-stable space for 7 days. Consistent bubbles will rise through the airlock for the first 3–5 days as yeast converts sugar to alcohol and CO2. Fermentation is complete when no bubbles pass through the airlock for 48 consecutive hours, and the liquid (now beer) is fully opaque and hazy.
Dry Hop and Add Fruit
Sanitize the carboy opening, then add the remaining 0.5 oz Citra hop pellets, 0.4 oz Mosaic hop pellets, and strained peach puree directly to the fermented beer. Reseal the airlock and let the beer rest for 3 more days at 68°F, away from direct sunlight, to infuse bright tropical hop aroma and sweet peach flavor. Avoid stirring to keep yeast sediment settled at the bottom of the carboy.
Bottle and Condition
Dissolve 0.75 oz corn sugar in 2 oz of boiling water, cool to room temperature, and add to the bottom of a clean sanitized bottling vessel. Use the auto-siphon to transfer finished beer from the carboy, mixing gently with the priming sugar to evenly distribute for consistent carbonation. Fill each 12oz amber glass bottle to 1 inch below the rim, then use the red bench capper to seal with sanitized crown caps. Let bottles condition at 68–72°F for 7 days to build natural carbonation, then chill for 48 hours before serving.
Tips
2.Always strain fruit puree before adding to the fermenter: Unstrained fruit with skin, seeds, or pulp can introduce unwanted astringency, and extra unfermented fruit sugar can cause over-carbonation or gushing bottles during conditioning.
3.Chill conditioned bottles for a full 48 hours before pouring: Cold temperatures help settle fine yeast and hop particles, creating the signature thick, creamy milkshake mouthfeel instead of a thin, watery pour, and supporting a long-lasting, fluffy white head.

Just bottled my third batch following this recipe! OMG the vanilla and lactose balance is SO good, brought a few 4-packs to our neighborhood potluck last weekend and everyone was asking where I bought it. Total game changer for anyone who’s been scared to try IPAs because they’re too bitter.
Tried this for my first ever milkshake IPA and it turned out way better than I expected! My son who’s in college came home for fall break and stole half the batch to bring back to his dorm. Only note is I added a little extra peach puree and it slapped.
Wait 17 days total from start to carb’d bottles? That’s way faster than the other milkshake IPA recipes I’ve tried. I’m prepping all my ingredients tonight to make this for our annual Halloween costume party, can’t wait to see how it turns out!
Ran into a little hiccup during dry hopping — I think I added the hops too early and got some weird grassy notes? Did I mess up the timeline here? Followed everything else to a T though, the base flavor is still really nice.
Game. Changer. I’ve been homebrewing for 6 years and this is easily the creamiest, most fruit-forward milkshake IPA I’ve ever made. Served it at my game night last Saturday and even my friends who only drink light lager were going back for seconds.
Quick question — do I really need to use lactose for this? I’m making a batch for a friend who’s lactose intolerant and I don’t want to leave them out of our fall bonfire hang.
My whole family loved this, even my picky teenage kids who usually turn their nose up at anything that isn’t hard seltzer! We did a taste test last night with my brother who works at a local craft brewery and he said it’s better than half the milkshake IPAs they have on tap right now. Wild for a medium-difficulty homebrew recipe.
Wait, does anyone else’s batch come out a little cloudier than the store bought milkshake IPAs? I’m not mad about it, the flavor is chef’s kiss, just curious if that’s normal! Added mango puree on day 4 of fermentation if that matters.
Just cracked open my first bottle last night and OMG, the vanilla bean note is unreal! I did half vanilla and half strawberry puree and it tastes like a boozy strawberry milkshake in the best way. Only downside is my carbonation was a little lower than I wanted? Any tips?
Made this for my partner’s birthday cookout last weekend and it was the star of the show! Everyone kept saying it tasted like the fancy $18/can IPAs from the fancy bottle shop downtown. 10/10 will be making this on repeat all fall.
Super nervous to try this because I’ve only ever made basic wheat beers before, but the medium difficulty rating didn’t feel too intimidating. Just finished pitching the yeast this morning, fingers crossed it turns out! How long do you all usually wait before cracking the first bottle after carbing?